x68k_usb: Add unimap
This commit is contained in:
tmk
parent
197ca82992
commit
b0573ba80e
5 changed files with 1342 additions and 65 deletions
|
|
@ -1,48 +1,45 @@
|
|||
#
|
||||
# Makefile for PJRC Teensy
|
||||
#
|
||||
|
||||
|
||||
# Target file name (without extension).
|
||||
TARGET = x68k_usb
|
||||
TARGET ?= x68k_usb
|
||||
|
||||
# Directory common source filess exist
|
||||
TMK_DIR = ../../tmk_core
|
||||
TMK_DIR ?= ../../tmk_core
|
||||
|
||||
# Directory keyboard dependent files exist
|
||||
TARGET_DIR = .
|
||||
TARGET_DIR ?= .
|
||||
|
||||
# keyboard dependent files
|
||||
SRC = keymap.c \
|
||||
matrix.c \
|
||||
# project specific files
|
||||
SRC ?= matrix.c \
|
||||
led.c \
|
||||
protocol/serial_uart.c
|
||||
|
||||
CONFIG_H = config.h
|
||||
|
||||
|
||||
# MCU name, you MUST set this to match the board you are using
|
||||
# type "make clean" after changing this, so all files will be rebuilt
|
||||
#MCU = at90usb162 # Teensy 1.0
|
||||
#MCU = atmega32u4 # Teensy 2.0
|
||||
#MCU = at90usb646 # Teensy++ 1.0
|
||||
#MCU = at90usb1286 # Teensy++ 2.0
|
||||
MCU = atmega32u2 # Teensy 2.0
|
||||
|
||||
# MCU name
|
||||
# atmega32u4 Teensy2.0
|
||||
# atemga32u4 TMK Converter rev.1
|
||||
# atemga32u2 TMK Converter rev.2
|
||||
MCU ?= atmega32u2
|
||||
|
||||
# Processor frequency.
|
||||
# Normally the first thing your program should do is set the clock prescaler,
|
||||
# so your program will run at the correct speed. You should also set this
|
||||
# variable to same clock speed. The _delay_ms() macro uses this, and many
|
||||
# examples use this variable to calculate timings. Do not add a "UL" here.
|
||||
F_CPU = 16000000
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU ?= 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
ARCH ?= AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
|
|
@ -55,69 +52,58 @@ ARCH = AVR8
|
|||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
F_USB ?= $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in bytes
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Atmel DFU loader 4096
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# *Comment out* to disable the options.
|
||||
# comment out to disable the options.
|
||||
#
|
||||
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||||
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
||||
#NKRO_ENABLE = yes # USB Nkey Rollover
|
||||
#UNIMAP_ENABLE = yes
|
||||
#ACTIONMAP_ENABLE = yes # Use 16bit actionmap instead of 8bit keymap
|
||||
#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
|
||||
|
||||
|
||||
|
||||
#---------------- Programming Options --------------------------
|
||||
AVRDUDE = avrdude
|
||||
# Type: avrdude -c ? to get a full listing.
|
||||
AVRDUDE_PROGRAMMER = avr109
|
||||
AVRDUDE_PORT = /dev/ttyACM0
|
||||
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
|
||||
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
|
||||
|
||||
# Uncomment the following if you want avrdude's erase cycle counter.
|
||||
# Note that this counter needs to be initialized first using -Yn,
|
||||
# see avrdude manual.
|
||||
#AVRDUDE_ERASE_COUNTER = -y
|
||||
|
||||
# Uncomment the following if you do /not/ wish a verification to be
|
||||
# performed after programming the device.
|
||||
#AVRDUDE_NO_VERIFY = -V
|
||||
|
||||
# Increase verbosity level. Please use this when submitting bug
|
||||
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
|
||||
# to submit bug reports.
|
||||
#AVRDUDE_VERBOSE = -v -v
|
||||
|
||||
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
|
||||
#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
|
||||
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
|
||||
|
||||
PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
|
||||
#
|
||||
# Keymap file
|
||||
#
|
||||
ifeq (yes,$(strip $(UNIMAP_ENABLE)))
|
||||
KEYMAP_FILE = unimap
|
||||
else
|
||||
ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
|
||||
KEYMAP_FILE = actionmap
|
||||
else
|
||||
KEYMAP_FILE = keymap
|
||||
endif
|
||||
endif
|
||||
ifdef KEYMAP
|
||||
SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
|
||||
else
|
||||
SRC := $(KEYMAP_FILE).c $(SRC)
|
||||
endif
|
||||
|
||||
|
||||
# Search Path
|
||||
VPATH += $(TARGET_DIR)
|
||||
VPATH += $(TMK_DIR)
|
||||
|
||||
|
||||
include $(TMK_DIR)/protocol.mk
|
||||
include $(TMK_DIR)/protocol/lufa.mk
|
||||
include $(TMK_DIR)/protocol.mk
|
||||
include $(TMK_DIR)/common.mk
|
||||
include $(TMK_DIR)/rules.mk
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue