initial attempt for LUFA.

Add keyboard/lufa macway keyobard with LUFA.
Add new program target to rule.mk; flip, dfu and teensy

keyboard/lufa/Makefile

@@ -0,0 +1,161 @@
+# Hey Emacs, this is a -*- makefile -*-
+#----------------------------------------------------------------------------
+# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
+#  >> Modified for use with the LUFA project. <<
+#
+# Released to the Public Domain
+#
+# Additional material for this makefile was written by:
+# Peter Fleury
+# Tim Henigan
+# Colin O'Flynn
+# Reiner Patommel
+# Markus Pfaff
+# Sander Pool
+# Frederik Rouleau
+# Carlos Lamas
+# Dean Camera
+# Opendous Inc.
+# Denver Gingerich
+#
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device, using avrdude.
+#                Please customize the avrdude settings below first!
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make doxygen = Generate DoxyGen documentation for the project (must have
+#                DoxyGen installed)
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+
+# Target board (see library "Board Types" documentation, NONE for projects not requiring
+# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
+# "Board" inside the application directory.
+BOARD = USBKEY
+
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Target file name (without extension).
+TARGET = lufa
+
+
+# Path to the LUFA library
+LUFA_PATH = ../../protocol
+
+# Create the LUFA source path variables by including the LUFA root makefile
+include $(LUFA_PATH)/LUFA/makefile
+
+
+
+# List C source files here. (C dependencies are automatically generated.)
+LSRC = $(TARGET).c                                                 \
+	  Descriptors.c                                               \
+	  $(LUFA_SRC_USB)                                             \
+	  $(LUFA_SRC_USBCLASS)
+
+SRC = $(subst $(LUFA_PATH)/LUFA/,,$(LSRC))
+SRC +=	keymap.c \
+	matrix.c \
+	led.c \
+	sendchar_null.c
+CONFIG_H = config.h
+
+
+
+# LUFA library compile-time options and predefined tokens
+LUFA_OPTS  = -D USB_DEVICE_ONLY
+LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8
+LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1
+LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
+LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
+
+OPT_DEFS  = -DF_CPU=$(F_CPU)UL
+OPT_DEFS += -DF_USB=$(F_USB)UL
+OPT_DEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
+OPT_DEFS += $(LUFA_OPTS)
+
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(LUFA_PATH)/LUFA
+
+
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
+
+test:
+	echo $(SRC)